This is that PDP 11/45 emulator which is put together from my earlier
PDP 11/70
emulator. Because a PDP 11/45 has less memory it cannot run some of the software a PDP 11/70 can.
The PDP 11/45 was released in 1972 and is an older less powerful version of the PDP 11/70 which was released in 1975. It is the second implementation of the PDP 11 following on from the PDP 11/20, which had an odd coupling of a 16 address bit processor to an 18 address bit bus. Naturally then, the PDP 11/45 had to include some form of memory management!
The PDP 11/45 has the same processor as the PDP 11/70 but lacks 22 bit addressing, restricting it to 124KW of memory instead of 4MB. It also lacks unibus mapping and a number of the PDP 11/70's special control registers. But still it has three addressing modes (Kernel, Supervisor, and User) and implements split Instruction and Data addressing. Split I&D cause Instruction memory references based on the the use of the program counter to map seperately from general Data addressing. As a result a program can have 32768 words of instruction memory
AND
32768 words of data. Some of the newer operating systems such as BSD require this to fit programs into memory. Sadly a PDP 11/45 can't run BSD because the system maximum memory limit of 124KW is not sufficient to load the entire operating system.
One wonders if these types of memory restrictions, which ultimately killed the PDP 11, influenced the design of Unix to be more modular. Perhaps leading to things like shell piping of data between small programs.
Note: The boot code in this emulator is a custom PDP 11 program running with it's own set of light patterns. It is initially loaded at address 140000 and the LIGHTS command operates by mapping a WAIT instruction to different addresses within Supervisor mode. The source for this program can be found in the RT11 operating environment as
BOOT.MAC
You can use this code to boot one of the guest OSes or use the LIGHTS command and DIAG command to experiment with idle light patterns and load test the CPU.
If you wish to toggle in a simple light chaser to the front panel then here are some switch commands which can be used:
To restart the initial boot code (if it has not been overwritten) use the switch commands:
HALT, 140000, LOAD ADDRESS, START
There are many PDP emulators out there and I have never seen what I consider to be a complete list. Some of the really interesting ones can be found by googling terms such as "vhdl pdp 11". However the gold standard seems to be SIMH at
Trailing Edge
. A different approach to Javascript PDP 11 emulation can be found at
www.pcjs.org
.
I believe that the first PDP 11 emulator would be SIM-11 written in FORTRAN before the first PDP 11/20 hardware was even built - see
How the PDP-11 Was Born
. There is more PDP 11 history at
www.hampage.hu
.
Of course if you want your own PDP 11/70 front panel you might consider a
PiDP-11
.
Happy emulating!
Paul Nankervis
List of guest OS's:
Disk
OS
Comment
RK0
Unix V5
Boot using:
unix
then login as
root
RK1
RT11 v4.0
The lightest/fastest OS here
RK2
RSTS V06C-03
Boot and login as
1,2
with password
SYSTEM
or as
11,70
using
PDP
RK3
XXDP
Diagnostic OS and utilities
RK4
RT-11 3B
Distribution for RT-11 Version 3B
RK5
RT-11 V5.4F
Distribution for RT-11 Version 5.4F
RL0
BSD 2.9
Boot using:
rl(0,0)rlunix
CTRL/D to get to multiuser
RL1
RSX 11M v3.2
Fails on a PDP 11/45
RL2
RSTS/E v7.0
Option: <LF> Suboption: <LF> ... Login as
1,2
using
SYSTEM
or
11,70
using
PDP
RL3
XXDP
Larger version of diagnostics - including PDP 11/70 utilities
RP0
ULTRIX-11 V3.1
CTRL/D to enter multiuser mode. Login as
root
with no password
RP1
BSD 2.11
Fails on a PDP 11/45
RP2
RSTS/E v9.6
Answer boot questions and login as
1,2
(password
SYSTEM
) or
11,70
(no password)
RP3
RSX 11M v4.6
Starts logged in as
1,2
(password
SYSTEM
) - user accounts
200,1
(no password) or
11,70
(password
PDP
)
Note:
Disks are shown in approximately order size. The
RK05
disks at the top are small and not too bad to use across a network.
The
RP06
disks at the bottom can be rather slow.
BOOT>
boot rk0
@
unix
login:
root
#
date
Fri Mar 21 12:09:02 EST 1975
#
chdir /etc
#
pwd
../etc
#
ls -al
total 40
drwxr-xr-x 2 bin 240 Mar 21 12:07 .
drwxr-xr-x 9 bin 160 Jan 29 16:14 ..
-rwxr--r-- 1 bin 474 Nov 26 18:13 getty
-rwxr-xr-x 1 bin 1446 Nov 26 18:13 glob
-rwxr--r-- 1 bin 1972 Nov 26 18:13 init
-rwxr-xr-x 1 bin 814 Nov 26 18:13 lpd
-rwxr--r-- 1 bin 4136 Nov 26 18:13 mkfs
-rwxr--r-- 1 bin 1800 Nov 26 18:13 mknod
-rwsr-xr-x 1 root 2078 Nov 26 18:13 mount
-rw-r--r-- 1 bin 49 Nov 26 18:13 passwd
-rw-r--r-- 1 bin 70 Nov 26 18:13 rc
-rw-r--r-- 1 bin 56 Nov 26 18:13 ttys
-rwsr-xr-x 1 root 1990 Nov 26 18:13 umount
-rwxr-xr-x 1 bin 32 Nov 26 18:13 update
-rw-r--r-- 1 root 144 Mar 21 12:09 utmp
#
cat /etc/passwd
root::0:1::/:
daemon::1:1::/bin:
bin::3:1::/bin:
#
cal 10 1981
Oct 1981
S M Tu W Th F S
1 2 3
4 5 6 7 8 9 10
11 12 13 14 15 16 17
18 19 20 21 22 23 24
25 26 27 28 29 30 31
#
ls -al /bin
total 339
drwxr-xr-x 2 bin 944 Nov 26 18:13 .
drwxr-xr-x 9 bin 160 Jan 29 16:14 ..
-rwxr-xr-x 1 bin 1514 Nov 26 18:13 ar
-rwxr-xr-x 1 bin 7308 Nov 26 18:13 as
-rwxr-xr-x 1 bin 6042 Nov 26 18:13 bas
-rwxr-xr-x 1 bin 152 Nov 26 18:13 cat
-rwxr-xr-x 1 bin 5668 Nov 26 18:13 cc
...
Example boot of RT11 v4.0
BOOT>
boot rk1
RT-11SJ V04.00C
.D 56=5015
.TYPE V4USER.TXT
Welcome to RT-11 Version 4. RT-11 V04 provides new hardware support
and some major enhancements over Version 3B
...
.D 56=0
.
MAC BOOT
ERRORS DETECTED: 0
.
LINK BOOT
.
DIR BOOT
BOOT .MAC 16 BOOT .OBJ 4
BOOT .SAV 4
3 Files, 24 Blocks
2851 Free blocks
.
DIR
SWAP .SYS 25 01-Feb-82 RT11BL.SYS 65 01-Feb-82
RT11SJ.SYS 67 01-Feb-82 RT11FB.SYS 80 01-Feb-82
TT .SYS 2 01-Feb-82 DT .SYS 3 01-Feb-82
DP .SYS 3 01-Feb-82 DX .SYS 3 01-Feb-82
...
Example boot of RSTS V06C-03
BOOT>
boot rk2
RSTS V06C-03 Vixen (DK2)
Option:
ST
You currently have: JOB MAX = 31, SWAP MAX = 28K.
JOB MAX or SWAP MAX changes?
N
Default memory allocation table specifies nonexistent memory.
Table will be reset by RSTS.
Memory allocation table:
0K: 00000000 - 00147777 ( 26K) : EXEC
26K: 00150000 - 00247777 ( 16K) : RTS (BASIC)
42K: 00250000 - 00757777 ( 82K) : USER
124K: 00760000 - End : NXM
Table suboption?
You currently have crash dump disabled.
DD-MMM-YY?
31-OCT-76
12:00 PM?
11:45
INIT V06C-03 RSTS V06C-03 Vixen
Command File Name?
DETACHING...
HELLO
RSTS V06C-03 Vixen Job 2 KB0 31-Oct-76 11:45 AM
#
11/70
Password:
PDP
Ready
DIR/S
Name .Ext Size Prot Access Date Time Clu RTS Open
SY:[11,70]
ACEY .BAS 5 < 60> 31-Oct-76 31-Oct-76 07:19 AM 1 RT11 0
TREK .BAS 16 < 60> 31-Oct-76 31-Oct-76 06:58 AM 1 BASIC 0
TREK .DOC 9 < 60> 31-Oct-76 31-Oct-76 06:58 AM 1 RT11 0
ANIMAL.BAS 5 < 60> 31-Oct-76 31-Oct-76 06:59 AM 1 BASIC 0
STRTRK.BAS 27 < 60> 31-Mar-81 31-Mar-81 12:00 M 2 RT11 0
STRTR1.BAS 9 < 60> 31-Mar-81 31-Mar-81 12:06 PM 2 BASIC 0
ADVENT.DOC 4 < 60> 13-Mar-77 20-Jul-85 06:50 AM 1 RT11 0
ADVENT.SAV 93 <124> 13-Mar-77 20-Jul-85 06:50 AM 1 RT11 0
ADVENT.VAR 22 < 60> 13-Mar-77 20-Jul-85 06:50 AM 1 RT11 0
ADVTXT.TXT 125 < 60> 13-Mar-77 20-Jul-85 06:50 AM 1 RT11 0
SYSMAC.SML 42 < 60> 13-Mar-77 13-Mar-77 06:42 AM 1 BASIC 0
HELLO .MAC 1 < 60> 13-Mar-77 13-Mar-77 06:43 AM 1 RT11 0
BOOT .MAC 24 < 60> 13-Mar-77 13-Mar-77 06:43 AM 1 RT11 0
Total of 382 blocks in 13 files in SY:[11,70]
Ready
RUN ADVENT
WELCOME TO ADVENTURE!! WOULD YOU LIKE INSTRUCTIONS?
NO
YOU ARE STANDING AT THE END OF A ROAD BEFORE A SMALL BRICK BUILDING.
AROUND YOU IS A FOREST. A SMALL STREAM FLOWS OUT OF THE BUILDING AND
DOWN A GULLY.
EAST
YOU ARE INSIDE A BUILDING, A WELL HOUSE FOR A LARGE SPRING.
THERE ARE SOME KEYS ON THE GROUND HERE.
THERE IS A SHINY BRASS LAMP NEARBY.
THERE IS FOOD HERE.
THERE IS A BOTTLE OF WATER HERE.
TAKE FOOD
OK
TAKE KEYS
OK
LIGHT LAMP
YOUR LAMP IS NOW ON.
QUIT
DO YOU REALLY WANT TO QUIT NOW?
YES
OK
YOU SCORED 32 OUT OF A POSSIBLE 350, USING 6 TURNS.
YOU ARE OBVIOUSLY A RANK AMATEUR. BETTER LUCK NEXT TIME.
TO ACHIEVE THE NEXT HIGHER RATING, YOU NEED 4 MORE POINTS.
Ready
RUN TREK
ORDERS: STARDATE = 2000
AS COMMANDER OF THE UNITED STARSHIP ENTERPRISE, YOUR MISSION
IS TO RID THE GALAXY OF THE DEADLY KLINGON MENACE. TO DO THIS,
YOU MUST DESTROY THE KLINGON INVASION FORCE OF 22 BATTLE
CRUISERS. YOU HAVE 40 SOLAR YEARS TO COMPLETE YOUR MISSION.
( I.E. UNTIL STARDATE 2040 )
GIVE COMMAND 'END' TO STOP THE GAME EARLY.
DO YOU REQUIRE FURTHER INSTRUCTIONS? N
DO YOU WANT A CHART?
Y
1 2 3 4 5 6 7 8
---------------------------------
1 : : : : : : : : :
---------------------------------
2 : : : : : : : : :
---------------------------------
3 : : : : : : : : :
---------------------------------
4 : : : : : : : : :
---------------------------------
5 : : : : : : : : :
---------------------------------
6 : : : : : : : : :
---------------------------------
7 : : : : : : : : :
---------------------------------
8 : : : : : : : : :
---------------------------------
YOU ARE CURRENTLY IN QUADRANT 5 - 2
---------------
B . . . . . . .
. * . . . . . .
. . . . . . E .
. . . . . . . .
. . * . . . . .
* . . . . . . .
. . . . . . . .
. . . . . * . .
---------------
STARDATE: 2000 CONDITION: YELLOW
QUADRANT: 5 - 2 SECTOR: 7 - 3
ENERGY: 3000 PHOTON TORPEDOS: 10
KLINGONS: 22
COMMAND?
^C
Ready
SYSTAT
RSTS V06C-03 Vixen status at 31-Oct-76, 11:47 AM Up: 2:08
Job Who Where What Size State Run-Time RTS
1 [OPR] Det ERRCPY 5K SR 3.7 BASIC
2 [SELF] KB0 SYSTAT 8K RN Lck 4.6 BASIC
Busy Devices: None
Disk Structure:
Disk Open Free Cluster Errors Name Comments
DK2 3 315 1 0 VIXEN Pub, DLW
Small Large Jobs Hung TTY's Errors
385 1 2/2 0 0
Run-Time Systems:
Name Ext Size Users Comments
BASIC BAC 16(16)K 2 Perm, Addr:26, KBM, CSZ
RSX TSK 2(28)K 0 Non-Res, KBM
RT11 SAV 4(28)K 0 Temp, Addr:49, KBM, CSZ, EMT:255
RMS11 TSK 4(28)K 0 Non-Res
Message Receivers:
Name Job Msgs Max Senders
ERRLOG 1 0 40 Priv
Ready
RUN $SWITCH
Run-Time System to switch to?
RT11
.
MACRO HELLO=HELLO
ERRORS DETECTED: 0
.
LINK HELLO=HELLO
.
RUN HELLO
HELLO, WORLD!
.
BYE
Confirm:
Y
Saved all disk files; 384 blocks in use, 116 free
Job 2 User 11,70 logged off KB0 at 31-Oct-76 11:47 AM
System RSTS V06C-03 Vixen
Run time was 5.3 seconds
Elapsed time was 2 minutes
Good morning
Example boot of XXDP
BOOT>
boot rk3
CHMDKB1 XXDP+ DK MONITOR
BOOTED VIA UNIT 2
28K UNIBUS SYSTEM
ENTER DATE (DD-MMM-YY):
<CR>
RESTART ADDR: 152010
THIS IS XXDP+. TYPE "H" OR "H/L" FOR HELP.
.
D
ENTRY# FILNAM.EXT DATE LENGTH START
1 HDDKB0.SYS 2-JAN-70 2 000112
2 HMDKB1.SYS 2-JAN-70 17 000113
3 HDDKB1.SYS 2-JAN-70 2 000114
4 HSAAC4.SYS 8-DEC-82 24 000115
....
Example boot of BSD 2.9
BOOT>
boot rl0
:boot
45Boot
:
rl(0,0)rlunix
CONFIGURE SYSTEM:
xp 0 csr 176700 vector 254 attached
rk 0 csr 177400 vector 220 attached
hk ? csr 177440 vector 210 skipped: No CSR
rl 0 csr 174400 vector 160 attached
rp ? csr 176700 vector 254 interrupt vector already in use
ht 0 csr 172440 vector 224 skipped: No CSR
tm 0 csr 172520 vector 224 skipped: No CSR
...
Erase=^?, kill=^U, intr=^C
#
ls -al
total 546
drwxr-xr-x11 root daemon 512 Mar 7 09:00 .
drwxr-xr-x11 root daemon 512 Mar 7 09:00 ..
-rw-rw-r-- 1 root daemon 164 Sep 29 09:20 .cshrc
-rw-rw-r-- 1 root daemon 266 Mar 7 08:43 .login
-rw-rw-r-- 1 root superuse 2 Jul 26 16:00 .msgsrc
-rw-rw-r-- 1 root daemon 116 Mar 30 00:59 .profile
-rw-r--r-- 1 root superuse 56 Nov 20 16:03 2.9stamp
-rw-rw-r-- 1 root superuse 450 Mar 30 00:50 READ_ME
drwxrwxr-x 2 bin bin 1632 Nov 20 16:04 bin
-rwxrwxr-x 1 root superuse 23572 Mar 7 09:05 boot
...
#
cat /etc/passwd
root::0:2:The Man:/:/bin/csh
toor::0:2:The Man:/:
daemon:***:1:1:The devil himself:/:
sys:***:2:1::/:
bin:***:3:1::/:
uucp::4:1:UNIX-to-UNIX Copy:/usr/spool/uucppublic:/usr/lib/uucp/uucico
notes:***:5:1:Notesfiles maintainer:/usr/spool/notes:
anon:***:6:1:Notesfiles anonymous user:/usr/spool/notes:
news:***:7:1:News maintainer:/usr/spool/news:
wnj:ZDjXDBwXle2gc:8:2:Bill Joy,457E,7780:/a/guest/wnj:/bin/csh
dmr:AiInt5qKdjmHs:9:2:Dennis Ritchie:/a/guest/dmr:
ken:sq5UDrPlKj1nA:10:2:& Thompson:/a/guest/ken:
mike:KnKNwMkyCt8ZI:11:2:mike karels:/a/guest/mike:/bin/csh
carl:S2KiTfS3pH3kg:12:2:& Smith,508-21E,6258:/a/guest/carl:/bin/csh
joshua::999:2:&:/usr/games:/usr/games/wargames
#
CTRL/D
Wed Dec 31 16:04:16 PST 1969
/etc/fstab: No such file or directory
/usr/sys: No such file or directory
init: /dev/tty07: cannot open
...
Berkeley Unix 2.9BSD
:login:
root
Welcome to the 2.9BSD (Berkeley) UNIX system.
tty: Command not found.
#
ls -al /bin
total 1182
-rwxrwxr-x 1 bin bin 8692 Dec 31 16:59 #
drwxrwxr-x 2 bin bin 1632 Nov 20 16:04 .
drwxr-xr-x11 root daemon 512 Mar 7 09:00 ..
-rwxrwxr-x 2 bin bin 2917 Dec 31 16:59 [
-rwxrwxr-x 1 bin bin 30340 Mar 24 08:27 adb
-rwxrwxr-x 1 bin bin 9844 Dec 31 16:58 ar
-rwxrwxr-t 1 bin bin 5626 Sep 30 17:39 as
-rwxrwxr-x 1 bin bin 4508 Jan 18 08:22 cat
-rwxrwxr-t 1 bin bin 7314 Oct 9 04:04 cc
-rwxrwxr-x 1 bin bin 5096 Dec 31 16:59 chgrp
-rwxrwxr-x 1 bin bin 3364 Dec 31 16:59 chmod
...
Example boot of RSTS/E v7.0
BOOT>
boot rl2
RSTS V7.0-07 Vixen (DL2)
Option:
<LF>
You currently have: JOB MAX = 63, SWAP MAX = 31K.
Default memory allocation table specifies nonexistent memory.
Table will be reset by RSTS.
Memory allocation table:
0K: 00000000 - 00203777 ( 33K) : EXEC
33K: 00204000 - 00303777 ( 16K) : RTS (BASIC)
49K: 00304000 - 00757777 ( 75K) : USER
124K: 00760000 - End : NXM
Table suboption?
<LF>
You currently have crash dump enabled.
CRASH.SYS file of 50 blocks is not available
Crash dump automatically disabled
DD-MMM-YY?
31-OCT-81
12:00 PM?
12:00
INIT V7.0-07A RSTS V7.0-07 Vixen
Command File Name?
<CR>
DETACHING...
...
HELLO 1,2
Password:
system
Job 1 is detached under this account
Job number to attach to?
<CR>
1 other user is logged in under this account
WELCOME TO RSTS/E V7.0 TIME SHARING
Ready
PRINT "Hello world",PI*4
Hello world 12.5664
Ready
DIR
Name .Ext Size Prot Date SY:[1,2]
CREATE.LOG 3 < 60> 31-Oct-81
LOGIN .SAV 13 <232> 23-Sep-79
LOGOUT.SAV 11 <232> 23-Sep-79
PIP .SAV 50 <232> 23-Sep-79
...
Ready
SYSTAT
RSTS V7.0-07 Vixen status at 31-Oct-81, 12:01 PM Up: 1:53
Job Who Where What Size State Run-Time Pri/RB RTS
1 [SELF] Det ERRCPY 5/31K SR 7.5 0/6 BASIC
2 [SELF] KB0 SYSTAT 11/31K RN Lck 9.0 -8/6 BASIC
Busy Devices: None
Disk Structure:
Disk Open Free Cluster Errors Name Comments
DL2 2 5568 2 0 VIXEN Pub, DLW
Small Large Jobs Hung TTY's Errors
478 0 2/8 0 0
Run-Time Systems:
Name Ext Size Users Comments
BASIC BAC 16(16)K 2 Perm, Addr:33, KBM, CSZ
RT11 SAV 4(28)K 0 Temp, Addr:65, KBM, CSZ, EMT:255
TECO TEC 8(24)K 0 Non-Res
Resident Libraries: None
Message Receivers:
Name Job Msgs Max Senders
ERRLOG 1 0 40 Priv
Ready
Example boot of XXDP
BOOT>
boot rl3
CHMDLD0 XXDP+ DL MONITOR
BOOTED VIA UNIT 3
28K UNIBUS SYSTEM
ENTER DATE (DD-MMM-YY):
<CR>
RESTART ADDR: 152010
THIS IS XXDP+. TYPE "H" OR "H/L" FOR HELP.
.
D
ENTRY# FILNAM.EXT DATE LENGTH START
1 MMDP .SAV 3-MAR-83C 17 000310
2 MTDP .SAV 3-MAR-83C 17 000331
3 HSAAD0.SYS 3-MAR-83 24 000352
4 HSABC0.SYS 3-MAR-83 28 000402
5 HSACC0.SYS 3-MAR-83 27 000436
6 HSADB0.SYS 3-MAR-83 25 000471
7 HUDIB0.SYS 3-MAR-83 5 000522
8 HELP .TXT 3-MAR-83 14 000527
...
BOOT>
boot rp2
RSX-11M V4.6 BL56 124.K MAPPED
>RED DB1:=SY:
>RED DB1:=LB:
>MOU DB1:RSXM56
>@DB1:[1,2]STARTUP
>* PLEASE ENTER TIME AND DATE (HR:MN DD-MMM-YY) [S]:
<CR>
>TIM
00:00:11 29-APR-74
>* ENTER LINE WIDTH OF THIS TERMINAL [D D:132.]:
<CR>
>SET /BUF=TI:132.
>ACS SY:/BLKS=1024.
>;
>; This system startup command file (LB:[1,2]STARTUP.CMD) contains a
>; template of commands to initialize the queue print spooler and queue
....
>INS LB:[1,54]INI.TSK
>INS LB:[1,54]MAC.TSK
>@ <EOF>
>
BYE
Have a nice day
29-APR-74 00:00 TT0: logged off VIXEN
Example boot of RSTS V9.6
BOOT>
boot rp3
RSTS V9.6-11 VIXEN (DB3) INIT V9.6-11
Today's date?
31-OCT-86
Current time?
10:02
Start timesharing? <Yes>
<CR>
Cannot use extra 12K of buffers. Reduced to 11K.
Size of monitor has changed from 73K to 72K.
Default memory allocation table shows MORE
memory than INIT detects on this machine.
Adjusting memory table.
Not enough room for current allocation of XBUF.
Resetting memory table.
Memory allocation table:
0K: 00000000 - 00363777 ( 61K) : EXEC
61K: 00364000 - 00727777 ( 57K) : USER
118K: 00730000 - 00757777 ( 6K) : XBUF
Memory available to RSTS/E is 124K words.
31-Oct-86 10:02 AM
11 devices disabled
Proceed with system startup? <YES>
<CR>
Beginning RSTS/E system startup...
31-Oct-86 10:02 AM Installing monitor overlays
31-Oct-86 10:02 AM Mounting disks
31-Oct-86 10:02 AM Assigning logical names
31-Oct-86 10:02 AM Starting error logging
31-Oct-86 10:02 AM Setting system characteristics
31-Oct-86 10:02 AM Installing run-time systems and libraries
install/library/noaddress=unrestricted EDT$:EDT
^
?Memory would be fragmented
31-Oct-86 10:02 AM Setting terminal characteristics
31-Oct-86 10:02 AM Defining system commands
31-Oct-86 10:02 AM Setting printer characteristics
31-Oct-86 10:02 AM Starting spoolers
*** From [1,2] on KB0: at 10:02 AM 31-Oct-86
** RSTS/E is on the air...
Bugs?
Plenty! Especially in the places where I haven't managed to figure out what a real PDP 11/70 should do. :-( Core PDP 11/70
stuff is well documented but some lesser used system functions require reverse engineering to understand.
If you have something you want me to look at let me know and I'll prioritise. However always happy to accept fixes!
